Loading... Please wait...

Hover over image to zoom

  • SKU: 4002033
  • SKU: 4002033

Motogadget m-Unit V.2 Digital Control Unit

Shipping Cost:
Calculated at checkout
Shipping Timeframe:
Express post options available, have your order in 1-2 days!
Current Stock:

 Product Description

This product is a digital control unit for your bike that can be operated by push-button control or conventional switch controls mounted on the handlebar.

The control box, the 'heart' of the bike's electrical system, is used for switching all necessary vehicle components and also doubles as fuse panel.

About the size of a small cigarette packet, it is completely enclosed and is resistant to water, weather and vibrations. Mounted by two M5 screws and all cable connections are made using terminal blocks.

This unit ensures that all switching operations are digitally controlled by a microprocessor and the latest solid-state technology, completely without mechanical relays, taking vehicle electrical systems to a new level!


  • reduced standby current of 0.35 mA (equivalent to 0.00035 A) if alarm system off, and 0.48 mA (equivalent to 0.00048 A) if alarm system on - for longer battery life
  • alarm system triggered by position-independent MEMS 3D gravity sensor. Installation in every position possible
  • alarm system with adjustable pre-alarm and adjustable levels of sensitivity
  • alarm system can be deactivated for easy transport mode
  • integrated parking light
  • voltage range of 3V to 20V 
  • can be used with 6V and 12V electrical systems
  • with extended voltage range, starting of an engine with a large displacement or high compression is no longer a problem
  • protected against reverse polarity
  • protected against overvoltage
  • extreme cable reduction by integrating all cables of switch or push buttons control including brake light switch in the handlebar. With only one cable the m-Unit V.2 is operated via a digital bus technology (product m-Button is required)


  • L/W/H: 101 x 61 x 28 mm
  • Weight: approx. 180g
  • Fixture: 2 x M5 screws, stainless steel (mounting and ground terminal), 1 x M5 screw-on terminal for battery positive
  • Operating voltage: 3V - 20V
  • Operating temperature: -20 °C... +80 °C
  • 1 x input (plus, switched) for ignition lock or m-Lock
  • 7 x pilot input (minus/ground, switched) for left turn signal, right turn signal, low beam/high beam, starter, horn, brake light, kill switch or setup respectively
  • 8 x output (plus) for left turn signal, right turn signal, low beam, high beam, starter, horn, brake light, AUX (switched plus for all other appliances)

What's Included:

  • m-Unit V.2
  • approx. 50 cm connector cable for battery plus terminal with 10 mm² nominal cross-section
  • 2 cable eyelets
  • 1 x M5 stainless steel screw
  • 2 x M5 stainless steel screw with nut
  • detailed installation and operating instructions


  • Control over handle bar push-buttons or conventional switch control units
  • Completely replaces the fuse panel Up to 8 independent circuits are digitally monitored and de-energized in case of failures. After removal of the fault, the safety feature is automatically reset
  • Diagnostics for all circuits use 15 status LEDs
  • Highest possible operational dependability with micro processor controlled and monitored switching operations
  • Flexible feature configuration due to simple device setup
  • No mechanical relays - newest generation semiconductors switch quickly, free of loss and wear.
  • Very compact dimensions
  • The m-Unit V.2 provides for hassle-free wiring and requires minimal wiring harnessing.
  • Control of high and low beam possible with only one push-button.
  • Digital hazard light control - stays on even after de-energising the main system.
  • Integrated digital, load independent flasher relay (like m-Flash), timer-controlled automatic deactivation.
  • Selectable flasher mode with fade-in/fade-out effect like with the m-Wave! timer-controlled automatic deactivation.
  • Navigation light feature selectable over all turn signals! Permanent low-light at each turn signal.
  • Integrated digital brake light modulator (like m-Stop), selectable flasher mode.
  • Integrated alarm system (gravity field sensor)
  • Intelligent deactivation of certain devices at engine startup
  • Only one cable required to control combined rear and brake lights
  • Completely water tight and vibration resistant

Questions & Answers

 Other Details

Ebay Store Category:

 Find Similar Products by Category

 Product Reviews

Write review

This product hasn't received any reviews yet. Be the first to review this product!

Click the button below to add the Motogadget m-Unit V.2 Digital Control Unit to your wish list.